1

Bender station 

To bend copper busbars up to 160*15 mm one by one

2

Digital controller for bender

To give instructions to the bender station to reach to perfect results 

3

Digital controller for puncher and cutter

To give instructions to the puncher and cutter station to reach to perfect results 

5

Hydraulic Power Pack

Equipped with one power pack

 

4

Puncher station

To punch copper busbars up to 160*15 mm one by one

Model: HBC-B160 ES/EH

Busbar Bender & Cutter & Puncher Machine

3 in 1 Electrical Busbar Machine

Bus bar Bending Machine | Punching and Cutting Machine Type B Introduction
As well as HBC-B120 this device is also works with one power pack which means the operator have access to all three stations (Punching, cutting and bending) but can work on each station at a time. The difference between this device and HBC-B120 is only in size of the busbar they could do operations on, which on this device the operator is able to process aluminum and copper busbars up to 160 × 15 mm.

INTRODUCTION

TECHNICAL INFORMATION

Bus bar Machine Type B Introduction
As well as HBC-B120 this device is also works with one power pack which means the operator have access to all three stations (Punching, cutting and bending) but can work on each station at a time. The difference between this device and HBC-B120 is only in size of the busbar they could do operations on, which on this device the operator is able to process aluminum and copper busbars up to 160 × 15 mm.

Busbar Machine Type B Features

Cutter station
The cutter station of this device is as precise and advanced as a whole busbar cutting machine.

The Cutting station of this device includes the following options:

– Precise cutting with high quality
– Perfect finishing after cutting
– Center oriented guide leads to the best result

Programmable Length Stopper cause high accuracy in positioning of cuts (optional)
– Could be programmed in absolute and incremental positions
– Programmable for 20 positions
– Rollers at two sides of cutter for ease of busbar movement
– Handy Length Stopper with high accuracy adjustment

Puncher station
Copper punching dies

In the punching process, the maximum busbar size that can be obtained is 15 x 160.
If you use a larger size busbar, it may cause damage to the operator as well as damage to the punch section.

The male and female dies are the main tools for punching and they are one of the most important and practical equipment of metal products and are made in different models. In all of them, the punching operation is done by two parts, the Male and female die, which punches the desired special shape from the raw sheet (Busbar). The location of the Male die is on the piston and the location of the female is on the main body.
Do not use the punching station to make holes on materials such as iron, etc. because it will break the male and female dies and damage the machine.

The Punching station of this device includes the following options:

– Laser pointer helps you to find the center of holes very easily
– Easy changeable dies
– None fixed stripper plate prevents fraction in dies
– Double acting hydraulic systems prevents sticking dies in busbar after punching process
– Guides could be moved up to center of dies
– Rollers at two side of puncher for ease of busbar system cause high accuracy in positioning of holes (Optional)
– Handy metering system with high accuracy adjustment
– Circle dies from M6 up to M18
– Oval and rectangle dies (Optional)

Bending Station
The bender of this device is equipped with two independent systems to achieve bending with high precision and repeatability to repeat bending process in a high number of times.

1-Rotary measuring system:

A rotary encoder with a pulse factor of 3600 pulses per revolution in couple is directly connected to the movable rotating plates of the bender. Since these plates are attached to the back of the busbar and rotates with it while bending process, the amount of rotation is directly
transferred to the encoder (5 Pulses each degree), Then, the bender controller system is online to adjust the bending amount and after reaching the desired bending angle, it ends the process.

2-Linear measuring system:

A digital ruler consists of a magnetic strip and a digital receiver attached to the end of the piston rod measures and controls the advance rate of the piston in each bending process. This system provides bend repeatability with an accuracy of 5 microns, which can lead to same size and numerous bends. It is also possible for the operator that instead of entering the angle from the beginning, enter the stroke length on the device screen. It should also be noted that the roller plate installed in the movable jaw section of the bender rotates dynamically during bending along with the busbar, which this design advantage prevents the bottom surface from being stretched. The Busbar moves forward on other surfaces and creates a line on the underside of the Busbar during bending. Among the other features of the bending section, it is possible to install a rod with different radii on the fixed jaw of the bender, which makes the bending arc more accurate in different thicknesses. 

HBC-B160-EH | HBC-B160-ES

MODEL

Cutting ,Punching and Bending Busbars One by One Function
Up to 160 x 15mm Bender capacity
Up to 160 x 15mm Cutting capacity
Circle dies: M6 up to M18
Oval and Rectangle Dies (Optional)
Punching capacity
Electronic Controller
High Accuracy Encoder
Bender controller
Step Mold (Optional)
Edge Bending Mold (Optional)
Twist Bending Mold (Optional)
End-Bending Mold (Optional)
Bender Molds
Laser Pointer Puncher center finder
Handy Length Stopper (EH)
Programmable Length Stopper (ES)
Length measuring in puncher and cutter
Three Separate Power Packs
Double Acting System
Hydraulic system
200 Bar Operating pressure
1 x 2.2 Kw Power rating
380 volt – 3/50 Hz Voltage
Hydraulic Oil H68 – 70 Liters Oil
200 x 110 x 100 (H) cm Main desk dimension
110 x 110 cm Roller desk dimension

FIND YOUR SOLUTION

FAQ's

Frequently asked questions

What is the difference between Type B and Type A?

The difference between HBC-B series and HBC-A series is that the Type B only has one power pack and the operators cannot work at the same time on each station like Type A series.

What is the difference between HBC-B120 and HBC-B160?

The difference between these machines is their capacity of processing on busbars, HBC-B120 is able to get used to process busbars up to 120 × 12 mm while HBC-B160 maximum busbar size is 160 × 15 mm.

Is programmable length stopper already installed on the device?

No, the programmable length stopper is optional and can be installed on the devices by order.

Is Laser Pointer in puncher already installed on the device?

No, like programmable length stopper the laser pointer is also an option that can be installed on puncher by order.

How can I get more Information about these machines?

You can fill up the sections below and email us. our experts will help you ASAP.
The other way is to go to "contact us" and make a call or send an email to the mentioned email on the page.

GET FREE QUOTE

NEED

CONSULTATION?

Feel free to contact us and

ask your question, its absolutely free.

    Related Products

    5/5 - (46 votes)