Is the DNC-010 rail cutter compatible with all DIN rail types?

Yes. The DNC-010 handles perforated and slotted profiles in both short and long sections. For special rail types, PAYAPRESS can custom-build the cutter based on your rail sample.

Does the DNC-010 leave burrs on the rail edge after cutting?

No. Because the blade and jaw shear through the rail instead of grinding it away, the edge comes out square and burr-free, requiring little or no finishing.

How are repeat cutting lengths set on the DNC-010?

Set the longitudinal stop along the 50 cm measuring ruler, lock it in place, and cut each rail against it. Every piece comes out at the exact same length without re-measuring.

Can the blade on the DNC-010 be replaced or resharpened?

Yes. The DNC-010 uses a durable high-strength steel blade that can be resharpened when it dulls or replaced when needed, keeping maintenance costs low.

Can the DNC-010 rail cutter be fixed to a workbench?

Yes. The DNC-010 can be bolted to a workbench with four bolts for stable workshop production, and its lightweight 67 × 60 × 47 cm frame also makes it easy to carry to the installation site.

Home ⪢ DIN Rail Cutter

Email is all we need — an engineer replies with pricing & the right configuration, as soon as possible.

DIN Rail Cutter

Clean, square PAYAPRESS DIN rail cuts without a hacksaw or an angle grinder. The DNC-010 is a bench DIN rail cutter that shears perforated and slotted rails to length with low force, leaving burr-free ends, and its 50 cm measuring ruler and stopper repeat every length.

Burr-Free

Shear Cut, No Grinding

Low Force

Easy, Safe Operation

50 cm Ruler

With Longitudinal Stopper

Custom Rails

Made From Your Sample

Download the catalog, or send us your rail sample and let an engineer walk you through the DNC-010. Both are free, form below.

Free download

Every machine, spec and configuration — in one PDF

Measure Once. Cut Clean.

DIN Rail Cutter for Panel Builders: Repeatable Lengths, No Burrs

Every DIN rail that goes into a panel is either sawn to length by hand or cut by a tool built for the job. A DIN rail cutter moves rail cutting into the second category, and the difference shows up in effort, finishing time, and how the finished panel looks. Among industrial electrical panel tools, it is one of the most practical additions to a panel shop’s bench. The next few minutes cover what the DNC-010 is, how it cuts, who it suits, and what drives its price.

What Is a DIN Rail Cutter?

A DIN rail cutter is a bench tool that cuts standardized mounting rails to length for panel assembly. The PAYAPRESS DNC-010 handles perforated and slotted profiles, short and long sections, and replaces the hacksaw and the angle grinder with clean, square, burr-free cuts and far less effort. It comes with a 50 cm measuring ruler and a stopper, so every length you set can be repeated exactly.

How the DNC-010 Cuts a DIN Rail

The rail sits under the clamp, and the blade and the jaw shear through it instead of grinding it away. Because the cut is a shear, the edge comes out square and burr-free, and it needs little or no finishing. To cut several pieces to the same length, set the longitudinal stop on the 50 cm ruler, lock it, and cut each rail against it. Low cutting force keeps the operation fast, safe and easy on the operator’s hands.

Main Features of the DNC-010 DIN Rail Cutting Tool

Effortless cutting. Low applied force makes every cut quick and easy.
Clean, burr-free ends. Components seat properly on the rail, and the panel looks professional.
Measuring ruler and stopper. A 50 cm ruler and a longitudinal stop deliver repeatable lengths.
Wide rail compatibility. Perforated and slotted profiles, in short and long sections.
Custom design on request. For special rail types, the cutter can be built from your rail sample.
Durable steel blade. A high-strength blade that can be resharpened or replaced.
Lightweight and portable. Easy to carry from the workshop to the installation site.

Who Uses an Industrial Rail Cutter?

Anyone who cuts DIN rails often will notice the difference quickly:

Electrical panel assembly lines and electrical cabinet production
Cable tray and wiring work
Installation and maintenance teams in office, commercial and industrial buildings
Electrical workshops that need accurate, repeatable rail cutting

Why a DIN Rail Cutter Beats a Hacksaw or Angle Grinder

A hacksaw is slow and leaves rough edges, and an angle grinder is loud, messy and hard to control. The DNC-010 shears the rail cleanly, so installers spend less time deburring and filing, equipment sits properly on the rail, and rework drops. The measuring guide and stop raise productivity on repeat cuts, and clean, precise cuts mean lower tool wear, low maintenance cost and a long blade service life.

Cutting Safely and Keeping the Blade Sharp

Make sure the rail is fully secured under the clamp before you cut.
Wear safety glasses and protective gloves.
Keep the blade edge clean, and sharpen or replace it if it becomes dull.
After setting the required length, lock the longitudinal stop securely.

DIN Rail Cutter Price

DIN rail cutter price depends on the configuration and on any customization for special rails, so compare quotations on equal specifications, not headline figures. PAYAPRESS manufactures the DNC-010 itself, which means direct pricing and engineering support from the people who built the tool. Request a quotation, or send us a sample of your rail to check that the cutter fits it.

DIN Rail Cutting

Clean, burr-free cuts

CE

EU safety certified

INDUSTRY 4.0

Connected production

Why PAYAPRESS

We don't sell machines. We remove risks.

Warranty, service, delivery, customization — every DNC-010 arrives with all of it handled.

12 Months Warranty

One year, no questions asked

Every DNC-010 leaves the factory with a 12-month manufacturer's warranty covering parts and workmanship.

10 YEARS

After-sales service with MATE

A decade of spare parts, remote diagnostics and engineering support — with tooling supplied worldwide through MATE Precision Technologies.

INDUSTRY 4.0

The machine keeps score

The machine keeps its own record. Output, cycle counts and job history, reported without anyone writing anything down.

European conformity

Designed and tested to European safety standards, with full CE documentation for import, insurance and audits.

SAFE & FAST DELIVERY

It arrives like it left

protected shipping to wherever your workshop is.

Local Representation

Buy in your own language

Our representatives handle the quote, the order and the paperwork locally — you deal with someone in your market, in your language, not with a form on a website.

DNC-010

Din rail cutter DNC-010 Specifications

Process & Capacity

Model DNC-010

Function Cutting DIN rails to length

Rail types Perforated & slotted profiles

Section lengths Short and long sections

Cutting method Shear cut (blade and jaw)

Edge quality Clean, square, burr-free

Custom rails Built from the customer's rail sample

Tooling & Precision

Length setting 50 cm measuring ruler + longitudinal stop

Repeat cuts Lockable stop for identical lengths

Blade Durable high-strength steel

Blade service Replaceable and resharpenable

Operation & Machine

Cutting force Low, effortless operation

Safety High level of operator safety

Type Bench tool

Weight Lightweight and portable

Frequently Asked Question

Straight answers on the DNC-010

What is a DIN rail cutter used for?

A DIN rail cutter cuts standardized mounting rails to length for panel assembly. The PAYAPRESS DNC-010 replaces the hacksaw and the angle grinder with clean, square cuts and far less effort.

Is the DNC-010 compatible with all DIN rail types?

It is suitable for short and long DIN rail sections, including perforated and slotted profiles. For special rail types, a custom version can be built from your rail sample.

Are there burrs on the rail edge after cutting?

No. The blade and the jaw shear the rail instead of grinding it, so the cut is clean, square and burr-free. At most, minimal finishing is needed.

How do I cut several rails to the same length?

Use the 50 cm measuring ruler and the longitudinal stop. Set the length, lock the stop, and cut each rail against it for fast, consistent and repeatable results.

Is the blade replaceable?

Yes. The DNC-010 uses a durable high-strength steel blade that can be replaced or resharpened when it becomes dull.

Is the DNC-010 easy and safe to use?

Cutting needs only low force, and the tool is built for a high level of operator safety. Secure the rail under the clamp before every cut, and wear safety glasses and protective gloves.

Global representative network